Ostoskorin sisältö0  tuotetta - Yhteensä 0.00 €
« Takaisin

Cycle V3 tiedonkeruuyksikkö, nopeusnäytöllä

Hinta:180.00 €

Varastotilanne: Varastossa

V3 Direct Plug-In Cycle Analyst with Separate Speedometer

Dimensions: 128 x 57 x 26mm

140cm cable terminated with 6-pin JST-SM series connector.

Includes:

  • Analogger Cable
  • THUN Sensor Cable
  • Accessories Cabling
  • DC Power Cable
  • Handlebar Mounting Bracket
  • USB->TTL Programming Cable

The V3 Cycle Analyst is the next step for the CA product line to not only monitor what is going on in an ebike, but also control it.
In the V2 CA we included basic throttle over-ride capabilities for speed, current, and low voltage limiting that proved quite popular, but fundamentally it was mostly a passive display.

With the V3 Cycle Analyst, all the ebike signals, from your brake cutoffs to your
throttle to your pedal sensor, are first intercepted at the Cycle Analyst.
The CA then processes all of these inputs to determine how to control your bike, which it then does via one standard throttle output signal to the controller.

There are many advantages to this arrangement. In the traditional setup, any features that you wanted on the ebike, be it cruise control, torque sensing pedalec modes, temperature rollback etc. had to be supported by your particular motor controller. An OEM ebike company can designa custom controller that works with a specific set of input sensors, but DIY projects don’t have this luxury.

With the V3 Cycle Analyst, you have access to all these advanced sensor and control
schemes no matter what model motor controller powers your system.
Here are some of the more popular features you can include by using the V3 CA as your central ebike/EV console:
Thermal Rollback: A temperatures sensor input allows the V3 Cycle Analyst to scale back power as a motor heats up and prevent overheating damage.
PAS Sensor: The V3 Cycle Analyst can take the pedal pulse inputs of almost any ebike pedal rotation sensor to display your pedal cadence. It can use this to provide automatic power whenever you pedal (PAS mode) .
Torque Sensor: There is an analog input to sense a pedal torque sensor (such as the THUN
bottom bracket), display your human power input, and give proportional no-throttle pedalec
control.
Ebrakes: A digital input for ebrake sensors to plug in directly to the CA3, without needing to run another set of cables all the way down the bike to the controller.
Throttle Input Mapping: The CA3 can map your input throttle range to an output range suitable for the controller in order to eliminate dead-band zones at the beginning and end of the throttle motion.
Throttle Modes: Setup your throttle in Pass-Thru mode for conventional voltage control, or haveyour throttle directly regulate the battery current or motor power instead.
Throttle Ramps : Reduce the sensitivity and off-the-line kick of high power systems by setting ramp limits on the CA’s output throttle signal.
On the fly Limit Adjustments: Use a potentiometer or multi-position switch to instantly adjust any of your current/power/speed or pedal assist limits.Mode Presets: Configure up to three distinct power mode presets each with their own limit settings and PAS/Throttle behaviors, and then easily switch between them with a double button press.
Battery SOC and LVC: Accurate State Of Charge (SOC) estimator based on your cell chemistry and voltage. Configure up to two batteries each with their own details and Low Voltage Cutoffs.
Plus many advanced capabilities to discover, and of course all the functionality that you have in the V2 CA like volts, speed, amps, amp-hours, %regen, watt-hours/km etc. An official user manual has not yet been prepared, but almost all of the information is exceedingly well
documented in the unofficial users guide written by Endless-Sphere forum member Teklektik.

Varastossa - Saatavissa Keravalla.

Tuote: 60001